Logo

P0183 Engine Trouble Code

P0183 Engine

When you check engine light came on code P0183 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P0183 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

Theoretically you can drive a few more days or even months with a broken MAF sensor in your car. You will notice a decrease in gas mileage/km and over time the car will at the end start stalling a lot from engine side. At a shop, the replacement cost is between $300-$450 depending on the car, but that's usually the cost of parts because the labor is relatively simple.

P0183 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
1
Engine Oil Temperature Sensor Malfunction
8
Cylinder 1 Injector Circuit Low
3
Shift Solenoid E Performance or Stuck Off

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0183 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0183 OBD-II Trouble Code The fuel tank temperature sensor is used to detect the fuel temperature inside the fuel tank. The sensor modifies a voltage signal from the P0183 code. Engine Oil Temperature Sensor Malfunction and Cylinder 1 Injector Circuit Low causes most of code P0183.

Reason For P0183 Code

The reason of P0183 OBD-II Engine Trouble Code is Engine Oil Temperature Sensor Malfunction.

P0183 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair P0183 Code

Before starting let's see P0183 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0183 code stored in the ECU.
  • Technicians will note P0183 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

All functions are tested, lights, gauges, central display and warning functions. Once the unit is identified as faulty, we then move onto the rebuild stage. Each unit is fully stripped, all common failing components are then replaced with versions that are higher rated than standard. Once the rebuild is complete, we then retest the instrument cluster to ensure it functions in accordance with the manufacturers original specification.

If you suspect that your car has a defective mass air flow sensor, bring it to a certified mechanic so that a whole computer diagnostic can be run. In most situations, a defective mass flow sensor has a certain code that will process throughout computer diagnostics, and is normally simple to check into with computer testing equipment.

Sometimes P0183 code comes with P018300 code.

Diagnosis Of Engine Error OBD Code P0183

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0183 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0183 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.